Home > Parts
Choose a sub category:
Allis Chalmers Carburetor Farmall Cub Engine Refresh Ford Clutch
Ford Holley Carburetor Ford Hydraulics John Deere
Massey Ferguson Hydraulics Starter Magneto
Sort By:
Page of 6
O-Ring for Lift Cylinder O-Ring for Lift Cylinder

Single o-ring for the bottom of the lift cylinder.

Our Price: $0.80
PTO Cover Gasket PTO Cover Gasket

Gasket for PTO Cover

Fits a Ford 8N, 9N or 2N tractor

Our Price: $0.85
Side Cover Gasket Side Cover Gasket

Side door gasket

Fits Massey Ferguson: 1080, 1200, 1250, 133, 135, 135 US Built, 140, 148, 150, 152, 155, 158, 165, 165 US Built, 168, 175, 175 US Built, 178, 178 US Built, 180, 185, 188, 20, 20C, 20D, 20E, 20F, 2135, 230, 230 US Built, 231, 235, 240, 245, 250, 253, 255, 261, 265, 270, 275, 282, 282 US Built, 283, 285 (FR), 285 US Built, 290, 290 US Built, 298, 30B, 30D, 30E, 30H, 31, 3165, 35, 35 Gas / 35 Petrol, 35 US Built, 35X, 375E Brazilian, 390E Brazilian, 40, 40B, 40E, 50, 50A, 50B, 50C, 50D, 50E, 50EX, 50F, 550, 565, 575, 590, 595, 60, 65, 65 US Built, 670, 675, 690, 698, 699, TE20, TEA20, TED20, TEF20, TO20, TO30

OEM Part Numbers:
181217M1, 181217M2, 181217M3, 181217M6, 181217M4, 181217M5

Our Price: $0.95
Inspection Door Gasket Inspection Door Gasket

Gasket for side inspection door on differential.

Fits a Ford 2000, 2N, 4000, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 9N, NAA

Our Price: $0.95
Valve Chamber Gasket Valve Chamber Gasket

Gasket for valve chamber. If you're removing/replacing both sides, order a quantity of two.

Fits a Ford 8N, 9N or 2N tractor.

Our Price: $0.98
Set of Valve Keepers Set of Valve Keepers

Two-pieced set of valve keepers (also called valve locks) as pictured for a Cub C60 engine.

If you plan to put new keepers on your entire four-cylinder Cub C60 engine, order a quantity of "4" to get a total of eight keepers.

These keepers are directional--install with the tapered end at the top, larger end at the bottom.

Our Price: $0.99
Set of Gaskets for Pump Support Pegs Set of Gaskets for Pump Support Pegs

Set of two gaskets for pump support pegs.

Our Price: $1.25
Drain Plug Gasket Drain Plug Gasket

Transmission drain plug gasket.

Ford tractors: 2N, 9N, 8N, 501, 541, 600, 601, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 700, 701, 740, 741, 800, 801, 820, 821, 840, 850, 851, 860, 861, 900, 901, 941, 950, 951, 960, 961, 2000 (4 cylinder), 4000 (4 cylinder). Transmission/hydraulic filler plug. Ford: Tractor: 8N (if using updated shift cover), 501, 541, 600, 601, 620, 621, 630, 631, 640, 641, 650, 651, 660, 661, 700, 701, 740, 741, 800, 801, 820, 821, 840, 850, 851, 860, 861, 900, 901, 941, 950, 951, 960, 961, 2000 (3 and 4 cylinder), 2030, 2031, 2100, 2110, 2111, 2120, 2130, 2131, 2150, 2300, 2310, 3000, 3100, 3110, 3120, 3150, 3190, 3300, 3310, 3330, 4000 (3 and 4 cylinder), 4031, 4040, 4110, 4121, 4131, 4140. Industrial: 1801, 1821, 1841. Massey Ferguson: TE20, TEA20, TO20, TO30.

Our Price: $1.39
Pump Base Gasket Pump Base Gasket

Gasket for base of pump.

Fits a Ford 8N, 9N or 2N tractor

Our Price: $1.45
Carburetor-to-Manifold Gasket Carburetor-to-Manifold Gasket

Carburetor-to-manifold gasket for Holley carburetors found on Ford 2000, 3000, 4000 and 5000 series tractors.

Our Price: $1.45
Fuel Pump Gasket Fuel Pump Gasket

Fuel pump mounting gasket

Fits a Ford 2000 Series 3 Cyl 65-74, 2150, 2300, 231, 2310, 233, 2600, 3000 Series 3 Cyl 65-74, 3055, 3110, 3120, 3150, 3190, 3300, 3310, 333, 3330, 335, 3400, 3500, 3550 Indust/Const, 3600, 3600V, 4110, 4140, 4190, 420 Indust/Const, 4330, 4340, 4400, 4410, 4500 Indust/Const, 4600, 4600SU, 5000, 515 Indust/Const, 5190, 531, 5340, 535 Indust/Const, 550 Indust/Const, 5500 Indust/Const, 555 Indust/Const, 5550 Indust/Const, 6600

OEM: 82845245, C5NE9417A

Our Price: $1.45
Cork Gasket Cork Gasket

This cork gasket is installed behind the lift lever friction plate.

Fits a Ford 2000, 2N, 4000, 501, 600, 601, 700, 701, 800, 801, 8N, 900, 901, 9N, NAA or Ferguson TO20,TO30.

Our Price: $1.65
Hydraulic Lift Cover Gasket Hydraulic Lift Cover Gasket

Hydraulic lift cover gasket.

Fits Massey Ferguson models:135, 165, 175, 178, 178 US Built, 202, 204, 2135, 35, 35 Gas / 35 Petrol, 35 US Built, 35X, 40, 50, 65, 65 US Built, 765, TO35


Our Price: $1.75
Leather Washer for Piston Leather Washer for Piston

Leather washer for the NAA-style lift cylinder piston (GR1308) that we sell for the 8N, 9N and 2N tractors.



Our Price: $1.95
Gasket for Magneto to Governor Housing Gasket for Magneto to Governor Housing

Gasket for magneto to governor housing for Fairbanks-Morse FM series magnetos with a two-piece cap found on many Allis-Chalmers tractors.


Our Price: $2.50
Hydraulic Lift Pin Hydraulic Lift Pin

This pin slides through the connecting joint that attaches your arms to the top lid.

Fits Ford 2000, 2N, 3000, 3600, 4000, 4600, 501, 600, 700, 800, 8N, 900, 9N, NAA

Our Price: $2.50
O-Rings and Washers for Tube O-Rings and Washers for Tube

Two o-rings and two special washers for the hydraulic tube "standpipe". If you remove your tube or top-lid, consider replacing these o-rings and washers. You'll use one o-ring and washer on the top; and the other o-ring and washer on the bottom.

Our Price: $2.65
Individual Valve Spring Individual Valve Spring

Valve spring, sold individually, for the Farmall Cub C60 four-cylinder engine.

Our Price: $2.70
Rubber Backer for Piston Rubber Backer for Piston

Rubber back-up washer for the NAA-style piston (GR1308) that we sell for the 8N, 9N and 2N tractors.



Our Price: $3.20
Carburetor Gasket Kit for Zenith Carburetors Carburetor Gasket Kit for Zenith Carburetors

Carburetor gasket kit for Zenith # S906, S1203, 8561, 8627, 8691, 8781, 8808, 8928, 8979, 9167, 9635, 9636, 9667, 9705, 9706, 9707, 9725, 9749, 9752, 9804, 9805, 10002, 10136, 10386, 10432, 10441, 10498, 10514, 10522, 10697, 10698, 10699, 10850, 10902, 10903, 10981, 11080, 11106, 11141, 11142, 11506, 11522, 12401, 12613, 12632, 12749.

Please note: Many of the following tractors could also be equipped with a Marvel Schebler carburetor. Please verify the numbers and brand on your carburetor before ordering parts to ensure a proper kit is ordered.

These Zentih carburetors are often found on:

  • Allis Chalmers C, CA, D10, D12, D14, D15, WC, WD, WD45 and WF
  • Case R, S, VA, VAC
  • Co-Op E3
  • Cockshutt 30
  • Ford 9N, 2N, 8N
  • Farmall 130, 140, A, AV, B, BN, C, Super C, Super A,
  • Oliver 70

Our Price: $3.75
Draft Control Felt Seal Draft Control Felt Seal

This felt seat is used for the hydraulic lift draft control spring

Fits a Ford 9N, 2N, 8N, NAA, 600, 601, 700, 701, 800, 801, 900, 901, (1939-1962).

Our Price: $3.95
Individual Valve Guide Individual Valve Guide

Valve guide, sold individually, for the Farmall Cub C60 four-cylinder engine.

Our Price: $3.98
Hydraulic Draft Control Arm Pivot Pin Hydraulic Draft Control Arm Pivot Pin

This internal pin often breaks or wears, causing the hydraulics to not lift all the way. You'll need to heat up the arm to expand it; remove the old pin and insert the new one.
Fits a Ford 8N, NAA, Jubilee, 600, 700, 800 and 900 series tractors.

Our Price: $4.50
Clutch Pilot Bearing Clutch Pilot Bearing

Clutch pilot bearing for the 8N, 9N, 2N, Jubilee, NAA, 600, 700, 800, 900 series tractors as well as the following:


1800 Series 4 Cyl 59-60, 1801 Indust/Const, 1811 Indust/Const, 1821 Indust/Const, 1841 Indust/Const, 1871 Indust/Const, 1881 Indust/Const, 2000 3 Cyl Tractor, 2000 Series 4 Cyl 62-64, 2031, 2100, 2110 3 Cyl Tractor, 2110TR 4 Cyl, 2111, 2120 3 Cyl Tractor, 2120 4 Cyl, 2130, 2131, 2150, 2300, 230A, 231, 2310, 233, 234, 250C, 2600, 2600N, 2600R, 2600V, 260C, 2610, 2610V, 2810, 2910, 2N, 3000, 3055, 3100, 3110, 3120, 3150, 3190, 3230, 3300, 3310, 3310N, 333, 3330, 334, 335, 340, 3400, 340A, 340B, 3430, 345C Indust/Const, 345D Indust/Const, 3500, 3550 Indust/Const, 3600, 3600N, 3600NO, 3600R, 3600V, 3610, 3610NO, 3610V, 3900, 3910, 3910H, 3910N, 3910V, 3930, 3930H, 4000 Series 3 Cyl 65-74, 4000 Series 4 Cyl 62-64, 4030, 4031, 4040, 4100, 4110, 4110N, 4110O, 4110TR, 4110V, 4120, 4121, 4130, 4130N, 4130NO, 4131, 4140, 4190, 420 Indust/Const, 4200, 4330, 4340, 4400, 4410, 445 Indust/Const, 445A Indust/Const, 445C Indust/Const, 445D Indust/Const, 450 Indust/Const, 4500 Indust/Const, 455 Indust/Const, 4600, 4600NO, 4600O, 4600SU, 4610, 4610N, 4610NO, 4610O, 4610SU, 4610V, 4630, 4630N, 4630NO, 4630O, 4830, 4830N, 4830O, 5000, 501, 501 Series 4 Cyl, 5030, 5030O, 5100, 515 Indust/Const, 5190, 5200, 530A, 530B, 531, 5340, 535 Indust/Const, 540 Indust/Const, 540A Indust/Const, 540B Indust/Const, 541, 545 Indust/Const, 545A Indust/Const, 545C Indust/Const, 545D Indust/Const, 550 Indust/Const, 555 Indust/Const, 555A Indust/Const, 555B Indust/Const, 600, 600 Series 4 Cyl, 601, 601 Series 4 Cyl, 611, 620, 621, 63-64, 630, 631, 640, 641, 650, 651, 655 Indust/Const, 655A Indust/Const, 661, 671, 681, 700, 700 Series 4 Cyl, 701, 701 Series 4 Cyl, 740 Indust/Const, 741, 771, 800, 800 Series 4 Cyl, 801, 801 Series 4 Cyl, 811, 820, 821, 840, 841, 850, 851, 860, 861, 871, 881, 8N, 900, 900 Series 4 Cyl, 901, 901 Series 4 Cyl, 941, 951, 960, 961, 971, 981, 9N, Dexta, NAA, NAB, Super Dexta

Our Price: $4.95
Bearing Insulator Paper Bearing Insulator Paper

Insulator material for bearing installation on Fairbanks-Morse FM J series magnetos with a two-piece cap found on many Allis-Chalmers tractors.

Replaces Fairbanks Morse part number A2824.


Our Price: $4.95
John Deere Carburetor Gasket Kit John Deere Carburetor Gasket Kit

Carburetor Gasket Kit for John Deere tractors w/ Marvel Schebler # DLTX75, DLTX81, DLTX82, DLTX83, DLTX84, DLTX85, DLTX86, DLTX94, DLTX95, DLTX96, DLTX97, DLTX98, DLTX99, DLTX101, DLTX102, DLTX105, DLTX106, DLTX109U.

These carburetors are commonly found on JD 50, 60, 70, 520, 620, 720, 530, 630 and 730 tractors.
Please read the number on your carburetor before ordering to ensure that you order the correct part for your carburetor.

Our Price: $4.95
Oil Pan Gasket Oil Pan Gasket

Oil pan gasket for a Farmall Cub with a C60 engine.

Our Price: $6.75
Dip Stick Dip Stick

Hydraulic Dipstick

Fits a Ford 8N, 9N, 2N, Jubilee or NAA tractor.


Our Price: $6.95
Holley Main Needle with Spring Holley Main Needle with Spring

Idle needle with spring for Holley carburetors found on Ford 2000, 3000, 4000 and 5000 tractors.

Our Price: $6.95
Draft Control Nut Draft Control Nut

Draft Control Nut for Massey Ferguson tractors.

OEM part number: 180979M1, 180979M2

Fits Massey Ferguson 1080, 1085, 1200, 1250, 133, 135, 135 US Built, 140, 148, 150, 152, 158, 165, 165 US Built, 175, 175 US Built, 178, 178 US Built, 180, 185, 188, 20, 202, 204, 20C, 20D, 20E, 20F, 2135, 230, 230 US Built, 231, 235, 240, 245, 250, 253, 255, 261, 265, 270, 275, 282, 282 US Built, 283, 283 Brazilian, 285 (FR), 285 US Built, 290, 290 Brazilian, 290 US Built, 298, 30, 30B, 30D, 30E, 31, 3165, 340, 342, 35, 35 Gas / 35 Petrol, 350, 352, 355, 35X, 360, 362, 365, 372, 375, 375E Brazilian, 382, 383, 390, 390E Brazilian, 390T, 393, 396, 398, 399, 40, 40B, 40E, 50, 50C, 50D, 50E, 550, 565, 575, 590, 595, 65, 670, 675, 690, 698, 698T, 699, 765, TO35 and Massey Harris 50 tractors.

Our Price: $7.67